Category: Catalog
1884
JKS WT 750 winch trailer
The JKS WT 750 winch trailer can pull either a tow rope or a steel cable. The pulling force is limited to 1500 kg, but when needed it can be increased up to 2000 kg — so the pulling power never runs out. The actual pulling in the WT 750 is done with the CBW 1500 winch mounted directly on the trailer frame. If necessary, the winch can be detached from the trailer and moved to the edge of the trench, where it works as an independent unit. The product is manufactured in Finland, ensuring high quality and reliability. The WT 750 comes as standard with an LED work light,…
533
JKS pipe snake trailer PST 1000
The JKS pipe snake trailer PST 1000 makes installing underground cables easy. All you need to do is push the installation rod into the pipe, fasten the cable to the rod and pull the rod out of the pipe. If additional power is required, the trailer can be equipped with a winch. With the help of the JKS pipe snake trailer, ground cable installations can be carried out conclusively easier. The fibreglass rod is pushed into the pipe with the help of the pulling and pushing device, then the cable is attached to the rod and the rod is pulled back — the cable is pulled into the pipe. Pulling…
206
JKS split steel reel 75-2300
Large hot-dip galvanized steel reel for bundling old cables and lines or for unwrapping coils. The old material is wound onto the reel and tied into a bundle, after which the reel is opened in the middle — this way old cables can be conveniently bundled neatly. The reel can also be used for unwinding water pipe bundles. The pipe bundle is placed between the two reel halves and the whole package is lifted onto a reel trolley, gantry or hoist. After this, it is easy to disassemble the pipe spool as the spool rotates on a bearing-mounted shaft. The outer diameter of this reel is 2300 mm and the…
111
Split steel reel 60-1400
Hot galvanized steel reel for wrapping up old cables. The old cable is wrapped around the reel, then the reel must be split down the middle — as a result you get old cables in a nice package. The reel fits a 60 mm reel axle, and on request also a 75 mm axle. For use with JKS cable trailers and other cable working equipment.
1982
Split steel reel EW 60-1400
Hot galvanized and steel constructed wider reel for wrapping up old cables. The old cable is wrapped around the reel, then the reel must be split down the middle — as a result you get old cables in a nice package. The EW model is wider than the 60-1400 model (1100 mm), which allows larger cable packages to be wound. The reel fits a 60 mm reel axle, and on request also a 75 mm axle.
2257
Split XL-steel reel 60-2800
Extra-large and durable hot-dip galvanized steel reel for bundling cables and unwinding pipe coils. Designed for professional use, the reel makes it easy to bundle cables neatly and allows for effortless unwinding at construction sites, warehouses or recycling facilities. The reel structure enables cables or pipes to be placed between the two halves of the reel, making handling smooth with lifting equipment or reel trolleys. The galvanized steel ensures long-lasting durability and weather resistance, even in demanding conditions. The solution is ideal for electrical contractors, industrial applications and the recycling sector, where clean and efficient cable and pipe handling saves time and improves work safety. The reel fits a 60…
5400
JKS VEKA 90 cable pulling tool
The JKS VEKA 90 cable puller is suitable for work where the cable must be routed into a trench or pipe. The device is mounted on the excavator boom and is powered by the excavator hydraulics. VEKA 90 is an efficient and fast device that allows you to deal with the contract efficiently, which increases the economic benefits. The device has been designed with occupational safety in mind, so the risk of injury is reduced. The machine is available with different tool holders, for example S45 or S60. The customer can choose between 25 mm pulling tape, 6 mm steel wire and 6 mm pulling rope. Breaking strengths are 2500–3200…
10 024 04 41
ECO-Skate RF24 load moving system
ECO-Skate® ROTOHeavy-duty load moving system (360°) for the professional indoor heavy load transport on clean, smooth and level floors, incl. individually rotatable high-quality HTS wheels (abrasion-resistant, non-marking), anti slip rubber pad and attachment for alignment bars or pulling bars in various versions. Multifunctional and flexible due to the ability to block the wheel boxes with pins. It can be used like a fixed rear skate, equipped with an additional turntable like a steerable skate. In combination with an L-, S- or DUO load moving system with the same installation height, it forms a safe overall system with 3 load points (with secured load also as a 4-point system if the…
10 030 09 41
ECO-Skate RFN30 load moving system
ECO-Skate® ROTOHeavy-duty load moving system (360°) for the professional indoor heavy load transport on clean, smooth and level floors, incl. individually rotatable high-quality HTS wheels (abrasion-resistant, non-marking), anti slip rubber pad and attachment for alignment bars or pulling bars in various versions. Multifunctional and flexible due to the ability to block the wheel boxes with pins. It can be used like a fixed rear skate, equipped with an additional turntable like a steerable skate. In combination with an L-, S- or DUO load moving system with the same installation height, it forms a safe overall system with 3 load points (with secured load also as a 4-point system if the…
10 080 09 41
ECO-Skate RFN80 load moving system
ECO-Skate® ROTOHeavy-duty load moving system (360°) for the professional indoor heavy load transport on clean, smooth and level floors, incl. individually rotatable high-quality HTS wheels (abrasion-resistant, non-marking), anti slip rubber pad and attachment for alignment bars or pulling bars in various versions. Multifunctional and flexible due to the ability to block the wheel boxes with pins. It can be used like a fixed rear skate, equipped with an additional turntable like a steerable skate. In combination with an L-, S- or DUO load moving system with the same installation height, it forms a safe overall system with 3 load points (with secured load also as a 4-point system if the…
10 030 00 10
ECO-Skate i30L load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors, incl. pulling bar with grab handle or pulling eye, turntable with anti-slip rubber pad and high-quality 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with an S, DUO or two ROTO skates with the same installation height it forms a safe overall system with 3 load points.Turntable with anti-slip rubber pad and pulling bar with grab handle or pulling eye.3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Suitable for smooth and slightly uneven floors.Can be combined with S, DUO or…
10 120 03 41
ECO-Skate RFXN12 load moving system
ECO-Skate® ROTOHeavy-duty load moving system (360°) for the professional indoor heavy load transport on clean, smooth and level floors, incl. individually rotatable high-quality HTS wheels (abrasion-resistant, non-marking), anti slip rubber pad and attachment for alignment bars or pulling bars in various versions. Multifunctional and flexible due to the ability to block the wheel boxes with pins. It can be used like a fixed rear skate, equipped with an additional turntable like a steerable skate. In combination with an L-, S- or DUO load moving system with the same installation height, it forms a safe overall system with 3 load points (with secured load also as a 4-point system if the…
10 060 00 10
ECO-Skate i60L load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors, incl. pulling bar with grab handle or pulling eye, turntable with anti-slip rubber pad and high-quality 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with an S, DUO or two ROTO skates with the same installation height it forms a safe overall system with 3 load points.Turntable with anti-slip rubber pad and pulling bar with grab handle or pulling eye.3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Suitable for smooth and slightly uneven floors.Can be combined with S, DUO or…
10.011.07.40
ECO-Skate RM11 load moving system
ECO-Skate® ROTO MINIHeavy-duty transport skate (360°) for professional in-house movement of heavy loads on clean and level floors. Equipped with individually rotatable high-quality HTS 3-component polyurethane rollers (abrasion-resistant, non-marking, cut-resistant) and a non-slip load pad. In combination with an L, S or DUO system of the same installation height, these skates form a safe overall system with 3-point support (with appropriate securing and observance of the operating instructions, conditionally also with 4-point support).Individually rotatable HTS PU rollers (abrasion- and cut-resistant, non-marking).Non-slip pad for load support.ROTO MINI — compact and light (10.3 kg), capacity 1100 daN.Compatible with L, S and DUO systems of the same installation height.
10 060 00 20
ECO-Skate i60S load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors. Design incl. alignment bars, anti-slip rubber pad and high-quality HTS 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with a L- or possibly ROTO skates with the same installation height, it forms a safe overall system with 3 load points. With DUO or two ROTO load moving systems, observe the operating instructions for 4-point supports.Alignment bars and anti-slip rubber pad.Adjustable width according to the load (V).3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Combines with an L or ROTO skate…
10 060 00 30
ECO-Skate i60D load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors, incl. alignment bars, pulling bar with pulling eye, turntable with anti-slip rubber pad and high-quality HTS 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with a S, DUO or two ROTO trolleys with the same installation height, these trolleys form a complete system with 4 load points. Please note the steering angle of max. 45 °. If the steering angle of the skate system is fully utilized, there must be no additional steering angle of the traction unit…
10 120 00 10
ECO-Skate i120L load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors, incl. pulling bar with grab handle or pulling eye, turntable with anti-slip rubber pad and high-quality 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with an S, DUO or two ROTO skates with the same installation height it forms a safe overall system with 3 load points.Turntable with anti-slip rubber pad and pulling bar with grab handle or pulling eye.3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Suitable for smooth and slightly uneven floors.Can be combined with S, DUO or…
10 120 00 20
ECO-Skate i120S load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors. Design incl. alignment bars, anti-slip rubber pad and high-quality HTS 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with a L- or possibly ROTO skates with the same installation height, it forms a safe overall system with 3 load points. With DUO or two ROTO load moving systems, observe the operating instructions for 4-point supports.Alignment bars and anti-slip rubber pad.Adjustable width according to the load (V).3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Combines with an L or ROTO skate…
10 120 00 30
ECO-Skate i120D load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors, incl. alignment bars, pulling bar with pulling eye, turntable with anti-slip rubber pad and high-quality HTS 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with a S, DUO or two ROTO trolleys with the same installation height, these trolleys form a complete system with 4 load points. Please note the steering angle of max. 45 °. If the steering angle of the skate system is fully utilized, there must be no additional steering angle of the traction unit…
10 150 00 10
ECO-Skate i150L load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors, incl. pulling bar with grab handle or pulling eye, turntable with anti-slip rubber pad and high-quality 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with an S, DUO or two ROTO skates with the same installation height it forms a safe overall system with 3 load points.Turntable with anti-slip rubber pad and pulling bar with grab handle or pulling eye.3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Suitable for smooth and slightly uneven floors.Can be combined with S, DUO or…
10 150 00 20
ECO-Skate i150S load moving system
ECO-Skate® i-SeriesHeavy-duty load moving system for the professional indoor heavy load transport on clean, smooth and level floors. Design incl. alignment bars, anti-slip rubber pad and high-quality HTS 3-component polyurethane wheels, which are abrasion-resistant, cut-resistant and non-marking and suitable for all smooth and level floors with slight unevenness. In combination with a L- or possibly ROTO skates with the same installation height, it forms a safe overall system with 3 load points. With DUO or two ROTO load moving systems, observe the operating instructions for 4-point supports.Alignment bars and anti-slip rubber pad.Adjustable width according to the load (V).3-component polyurethane wheels: abrasion- and cut-resistant, non-marking.Combines with an L or ROTO skate…
NY2
Plastic hose clamp NY2 (Herbie Clip)
Pipe clamps from black nylon (polyamid 6.6) provide very strong, fast, reliable, non-corrosive and non-conductive pipe clamping. Working temperature of polyamid 6.6 is -40 to +105 °C (+105 °C continuously 500 hours), momentary 180 °C. Flammability according to UL 94 HB.
NY3
Plastic hose clamp NY3 (Ezyclik)
Pipe clamps from black nylon (polyamid 6.6) provide very strong, fast, reliable, non-corrosive and non-conductive pipe clamping. Working temperature of polyamid 6.6 is -40 to +105 °C (+105 °C continuously 500 hours), momentary 180 °C. Flammability according to UL 94 HB.
NY4
Plastic hose clamp NY4 (Ezyclamp)
Pipe clamps from black nylon (polyamid 6.6) provide very strong, fast, reliable, non-corrosive and non-conductive pipe clamping. Working temperature of polyamid 6.6 is -40 to +105 °C (+105 °C continuously 500 hours), momentary 180 °C. Flammability according to UL 94 HB.
01.060.40.10
ECO-Jack EJ60-4S hydraulic jack
ECO-Jack® S-SeriesECO-Jack® heavy duty hydraulic jacks are available in five different series with payloads up to 25 tons. The adjustability of the lifting claw on all ECO-Jack® is easy: Lift the claw with just one hand, take it horizontally out of the groove plate and insert it in a new position - done. Easy to use with a low risk of injury. The integrated pump requires no additional equipment. From the EJ100-3S, external manual or electric pumps can also be connected.Previously patented lifting claw. It ensures a safe lifting of the load and can be adjusted with one hand without tilting movement.A minimal self-weight. Improved construction and high-quality material have…
01.100.31.10
ECO-Jack EJ100-3S hydraulic jack
ECO-Jack® S-SeriesECO-Jack® heavy duty hydraulic jacks are available in five different series with payloads up to 25 tons. The adjustability of the lifting claw on all ECO-Jack® is easy: Lift the claw with just one hand, take it horizontally out of the groove plate and insert it in a new position - done. Easy to use with a low risk of injury. The integrated pump requires no additional equipment. From the EJ100-3S, external manual or electric pumps can also be connected.Previously patented lifting claw. It ensures a safe lifting of the load and can be adjusted with one hand without tilting movement.A minimal self-weight. Improved construction and high-quality material have…
01.150.31.10
ECO-Jack EJ150-3S hydraulic jack
ECO-Jack® S-SeriesECO-Jack® heavy duty hydraulic jacks are available in five different series with payloads up to 25 tons. The adjustability of the lifting claw on all ECO-Jack® is easy: Lift the claw with just one hand, take it horizontally out of the groove plate and insert it in a new position - done. Easy to use with a low risk of injury. The integrated pump requires no additional equipment. From the EJ100-3S, external manual or electric pumps can also be connected.Previously patented lifting claw. It ensures a safe lifting of the load and can be adjusted with one hand without tilting movement.A minimal self-weight. Improved construction and high-quality material have…
01.250.31.10
ECO-Jack EJ250-3S hydraulic jack
ECO-Jack® S-SeriesECO-Jack® heavy duty hydraulic jacks are available in five different series with payloads up to 25 tons. The adjustability of the lifting claw on all ECO-Jack® is easy: Lift the claw with just one hand, take it horizontally out of the groove plate and insert it in a new position - done. Easy to use with a low risk of injury. The integrated pump requires no additional equipment. From the EJ100-3S, external manual or electric pumps can also be connected.Previously patented lifting claw. It ensures a safe lifting of the load and can be adjusted with one hand without tilting movement.A minimal self-weight. Improved construction and high-quality material have…
01.030.50.10
ECO-Jack EJ30-5S hydraulic jack
ECO-Jack® S-SeriesECO-Jack® heavy duty hydraulic jacks are available in five different series with payloads up to 25 tons. The adjustability of the lifting claw on all ECO-Jack® is easy: Lift the claw with just one hand, take it horizontally out of the groove plate and insert it in a new position - done. Easy to use with a low risk of injury. The integrated pump requires no additional equipment. From the EJ100-3S, external manual or electric pumps can also be connected.Previously patented lifting claw. It ensures a safe lifting of the load and can be adjusted with one hand without tilting movement.A minimal self-weight. Improved construction and high-quality material have…
—
N-914 Cable gland with 8 mm sleeve
15.5 x 15.5 x 36 mm
—
Enclosure NB-204 IP-67 with molded cable entry
[TB80 x 50 x 25 mm] This high-quality enclosure is suitable for a wide range of applications, including junction boxes, embedded systems, transmitters, barometers, gas and humidity sensors, and temperature control and measurement devices.
—
Enclosure NE-510 IP-67 Alu Die-Cast
96 x 96 x 45 mm A durable and adaptable solution to protect your device, featuring two seals: one for protection against electromagnetic interference and the other for water protection, and well suited for use with pressure sensors, seismographs, embedded systems and amplifiers.
—
NE-301 IP-65 sealed aluminum enclosure
50 x 45 x 30 mm Made from cast material, they are durable and versatile and can be used in a variety of applications such as pressure sensors, seismographs, embedded systems and amplifiers.
—
NE-202 IP-67 highly durable plastic enclosure
52 x 50 x 35 mm An ideal choice for embedded systems, transmitters, barometers, gas and humidity sensors, temperature control and measurement applications that require a high level of protection.
—
NO210 IP67 ultra durable plastic enclosure
NO210 is a plastic enclosure with dimensions 115 × 65 × 40 mm. Suitable for embedded systems, transmitters, barometers, temperature, gas and humidity sensors and measuring devices where a high level of protection is required. A version made of ASA is also available for outdoor use, which is resistant to UV radiation and weathering.
—
NO202 IP67 flanged enclosures for harsh operating conditions
NO202 is a plastic enclosure with dimensions 84 × 50 × 39 mm. It is suitable for embedded systems, transmitters, barometers, temperature, gas and humidity sensors and measuring devices where a high level of protection is required. For outdoor use, a version made of ASA is also available, which is resistant to UV radiation and weathering.
—
NO1015 compact wall cabinet IP67
NO1015 series cabinets are a reliable solution electrical equipment protection both indoors and outdoors. Thanks to the IP67 protection class, they are fully dust and water resistant. Two depth options:: 100×150×70 mm and 100×150×85 mmBody os made of impact-resistant ABS or ASA for harsh conditions.Lid is standard or transparent (PC)TPE gasket for long-term tightness.Durable stainless steel locks.Mounting plate made of 1 mm galvanized steelAccessories: wall mount, post mount, internal doorCNC processing and UV printing possible
—
Stand for hose clamps
Stand for hose clamps 8.64 EUR. Size is 36,5 x36,5 cm. Prices are without VAT.
—
Pliers for deforamtion clamps
Pliers for deforamtion clamps allows the deformation of the ear clips without risk of abrupt. item price/pc Deformation pliers 22.8 EUR Prices are without VAT
—
Flexible screwdriver
Flexible screwdriver allows tightening clamps at difficult-access locations. item price/pc screwdriver, nut 7mm 7.92 EUR screwdriver, nut 6mm 7.92 EUR small screwdriver, nut 6mm 6.48 EUR Prices are without VAT
—
HSL Clips
This clip is inteded for thick-walled hose and is used in conditions with high loads (compressors construction, quarries, surface mining). Clip resists abrasion, impacts and other destructive influences. Simple assembly by two screws.>Material: galvanized iron Type size price/pc HSL - 29 22-29 1.68 EUR HSL - 34 29-34 1.68 EUR HSL - 40 33-40 2.52 EUR HSL - 49 40-49 3.36 EUR HSL - 60 48-60 3.84 EUR HSL - 76 58-76 4.56 EUR HSL - 94 77-94 6.6 EUR HSL - 115 94-115 8.64 EUR HSL - 400 89-101 8.76 EUR HSL - 463 103-113 9.84 EUR HSL - 525 106-127 12 EUR HSL - 550 115-130 13.2 EUR…
—
Hose clamp MAXI OPEN W1, W4
Hose clamp MAXI OPEN W1, W4', ' Hose clamp MAXI OPEN has quickly openable quick lock open, and therefore particularly suitable for fastening large diameter hose. Hose clamp is made of perforated design for a width of 12.7 mm. Material galvanized or stainless steel (17-20% chromium, 9-12% nickel) AISI 304, DIN 1.4301. diameter/width of clamps[mm] price/pc. MAXI OPEN W1 30-90/12,7 0,92 EUR MAXI OPEN W1 50-145/12,7 1,1 EUR MAXI OPEN W1 50-370/12,7 1,7 EUR MAXI OPEN W1 50-570/12,7 2,4 EUR MAXI OPEN W1 50-650/12,7 2,6 EUR MAXI OPEN W4 30-90/12,7 1,5 EUR MAXI OPEN W4 50-145/12,7 1,8 EUR MAXI OPEN W4 50-370/12,7 2,9 EUR MAXI OPEN W4 50-570/12,7 4,2 EUR…
—
Bridge hose clamp
Bridge clips are used for spiral hoses, of which the other clips have a problem with crossing the spiral. Bridge clamp with spiral tube wrapped completely around the perimeter. The direction of the spiral tube determines the type of bridge clamps, which are produced in a clockwise and left-handed version. Right-handed spiral hose so you will know that if it is also perpendicular to the body, so the spiral away from us in a clockwise direction. W4 bridge clamp is stainless steel (17-20% chromium, 9-12% nickel)AISI 304, DIN 1.4301. diameter / width of clamps[mm] price/pc MUSTEK W4 55-75/9 3 EUR MUSTEK W4 65-85/9 3 EUR MUSTEK W4 75-95/9 3.12 EUR…
—
Double wire clamps W1
Wired screw clamps are used to hose vrapovanĆ½m surface. The surface is screw clips too Robust clamp surface of the crush, which is not always desirable. Wired screw clamps are available in galvanized W1 and stainless steel variant W4. diameter / width of clamps[mm] Box prices Bag prices pc/box price/pc pc/bag price/pc DRAT W1 11-14 1000 0.19 EUR 100 0.26 EUR DRAT W1 13-16 1000 0.19 EUR 100 0.26 EUR DRAT W1 15-18 1000 0.19 EUR 100 0.26 EUR DRAT W1 17-20 1000 0.22 EUR 100 0.29 EUR DRAT W1 19-22 1000 0.22 EUR 100 0.29 EUR DRAT W1 20-24 1000 0.22 EUR 100 0.29 EUR DRAT W1 22-26 1000…
—
Single wire clamps W1
Self-locking wire clamps provide thier functions even if the temperature changes so they are used to join hoses in cooling or heating systems. Other dimensions of self-locking wire clamps are on order. diameter / width of clamps[mm] Box prices Bag prices pc/box price/pc pc/bag price/pc PERODRAT W1 6-9 1000 0.06 EUR 100 0.07 EUR PERODRAT W1 9-11 1000 0.06 EUR 100 0.07 EUR PERODRAT W1 11-13 1000 0.07 EUR 100 0.1 EUR PERODRAT W1 13-15 1000 0.08 EUR 100 0.11 EUR PERODRAT W1 15-18 1000 0.1 EUR 100 0.13 EUR Prices are without VAT
—
Spring clamps W1
Spring clamps (locking clamp) provide thier functions even if the temperature changes. Spring clamp for temperature changes may already provide sufficient clamping force around the circumference of the hose Spring locking clamps are therefore used to join hoses in cooling or heating systems. diameter / width of clamps[mm] Box prices Bag prices pc/box price/pc pc/bag price/pc PERO W1 6,0-7,3/8 1000 0.07 EUR 200 0.11 EUR PERO W1 7,6-8,3/8 1000 0.07 EUR 200 0.11 EUR PERO W1 8,6-9,5/8 1000 0.07 EUR 200 0.11 EUR PERO W1 8-11/8 1000 0.07 EUR 200 0.11 EUR PERO W1 9-12/8 1000 0.07 EUR 200 0.11 EUR PERO W1 10-13/8 1000 0.1 EUR 200 0.13 EUR…
—
Single ear clamps W4
Stainless steel hose clamps with deformation eyelet is intended for permanent connection, often is used in the automotive industry. Compared to All stainless steel clamps W4 is cheaper and space-efficient. Eyelet is deformated by pliers for deforamtion clamps. Made of stainless chromium-nickel steel (17-20% chromium, 9-12% nickel) AISI 304, DIN 1.4301. diameter / width of clamps[mm] Box prices Bag prices pc/box price/pc pc/bag price/pc DEF W4 5,5-6,5/5 1000 0.19 EUR 100 0.25 EUR DEF W4 6,0-7,0/5 1000 0.19 EUR 100 0.25 EUR DEF W4 7,0-8,7/5 1000 0.19 EUR 100 0.25 EUR DEF W4 7,8-9,5/5 1000 0.19 EUR 100 0.25 EUR DEF W4 8,8-10,5/5 1000 0.19 EUR 100 0.25 EUR DEF…
—
Double ear clamps W1
Hose clamps with deformation ears are used for permanent hose connection. Deformation clip is a cheaper alternative of Zinc coated steel clamps W1. Clamps are made of zinc coated unbreakable steel. To deform ears are used pliers for deforamtion clamps. diameter / width of clamps[mm] Box prices Bag prices pc/box price/pc pc/bag price/pc DEF W1 5-7/6 1000 0.1 EUR 200 0.12 EUR DEF W1 7-9/7 1000 0.1 EUR 200 0.13 EUR DEF W1 9-11/7 1000 0.12 EUR 200 0.17 EUR DEF W1 11-13/7 1000 0.12 EUR 100 0.17 EUR DEF W1 13-15/7,5 1000 0.13 EUR 100 0.17 EUR DEF W1 15-18/7,5 1000 0.14 EUR 100 0.19 EUR DEF W1 17-20/7,5…
—
Hobby W1
This is the perforated hose clamp w1 with destructive torque 15 Nm, that has hand tightening instead of screw. Hose straps for frequent assembly and disassembly without tools. Destructive torque: 15 Nm from size 14-27Material:completly galvanized diameter / width of clamps[mm] Box prices Bag prices pc/box price/pc pc/bag price/pc W1 hobby 8-16/8 1000 0.13 EUR 100 0.17 EUR W1 hobby 11-20/8 1000 0.14 EUR 100 0.18 EUR W1 hobby 14-27/12 500 0.18 EUR 50 0.24 EUR W1 hobby 18-32/12 500 0.19 EUR 50 0.25 EUR W1 hobby 21-44/12 500 0.22 EUR 50 0.29 EUR W1 hobby 27-51/12 500 0.22 EUR 50 0.3 EUR W1 hobby 33-57/12 500 0.23 EUR 50 0.31…
—
Endless band W2
For large diameters is ideal endless band with lock-in lock. Lock snaps into the desired location and tighten the screw. Assembly procedure is illustrated in plastic packaging. The endless band and lock is made of chrome steel (15-17% chromium) AISI 430, DIN 1.4016, galvanized steel screw. Comparison endless band W4 and W2. B>Endless band W2: chrome steel, the width of the band 9mm, length 30m, thread is extruded, snap-locpc, strap for easier application in plastic packagingEndless band W4: chrome-nickel steel, strip width of 8 or 14mm, length 3 or 25 meters, the thread is perforated, the lock is not clip, not in a plastic container. Part set price/pc Band W2,…